- Joined
- Dec 17, 2008
- Messages
- 28,185
Hi All!
I started looking for my 25th Anniversary upgrade stone some time around year 24 1/2. Unfortunately, due to my inability to make snap decisions,
I missed out on several stones that would have been excellent choices. Hence, this has turned into my 26th Anniversary upgrade instead of the
typical 25th! Anyway, here she is!





A really bad video because my phone stinks...but, I think you can see how sparkly it is!
(Sorry about all the background noise...I didnt know how to get rid of it.)
DK's IG video
Deets...
1.71 I/SI1 Whiteflash Expert Selection (7.7 mm)
.46 J/SI1 Super Ideal (I previously owned) (4.95 mm)
.46 I/SI1 (4.95 mm) Blue Nile
Ratio 64%
Setting by David Klass
2 tone
size 6.5
Design thread:
Special Thanks to the ladies who helped me with the design, especially Dreamer_D, MissGotRocks, Rfisher, LookinAgain, and
everyone who commented on my design thread. Input from others is so valuable in the design phase and much appreciated!
Shout out to Brittany at Whiteflash, who stuck with me for the year and a half until I could find "the one"! As usual, Whiteflash
was a pleasure to do business with!
Edit...Probably should thank my DH for putting up with me for the last 26 years!
I started looking for my 25th Anniversary upgrade stone some time around year 24 1/2. Unfortunately, due to my inability to make snap decisions,
I missed out on several stones that would have been excellent choices. Hence, this has turned into my 26th Anniversary upgrade instead of the
typical 25th! Anyway, here she is!





A really bad video because my phone stinks...but, I think you can see how sparkly it is!
(Sorry about all the background noise...I didnt know how to get rid of it.)
DK's IG video
Deets...
1.71 I/SI1 Whiteflash Expert Selection (7.7 mm)
.46 J/SI1 Super Ideal (I previously owned) (4.95 mm)
.46 I/SI1 (4.95 mm) Blue Nile
Ratio 64%
Setting by David Klass
2 tone
size 6.5
Design thread:
Hi Fellow PSers
Looking for a few eyes/input on my 3 stone CAD from DK. Anything out of order? The Round side stone is showing 1.95mm but
it should be 4.95 mm (which I think is correct in the drawing part of the CAD).
Here is the CAD from DK...

My current change is to
- move the 2 prongs on the side stone(s) to be inside of the 2 prongs of the Center stone. I don't want to see prongs if I don't have to.
Now, the side stone dilemma...
I'm not sure I like how they are set into the shank. I'm a little limited to what I can do because the setting is 2 tone...

Looking for a few eyes/input on my 3 stone CAD from DK. Anything out of order? The Round side stone is showing 1.95mm but
it should be 4.95 mm (which I think is correct in the drawing part of the CAD).
Here is the CAD from DK...

My current change is to
- move the 2 prongs on the side stone(s) to be inside of the 2 prongs of the Center stone. I don't want to see prongs if I don't have to.
Now, the side stone dilemma...
I'm not sure I like how they are set into the shank. I'm a little limited to what I can do because the setting is 2 tone...
- tyty333
- Replies: 92
- Forum: RockyTalky (Diamond Discussion)
Special Thanks to the ladies who helped me with the design, especially Dreamer_D, MissGotRocks, Rfisher, LookinAgain, and
everyone who commented on my design thread. Input from others is so valuable in the design phase and much appreciated!
Shout out to Brittany at Whiteflash, who stuck with me for the year and a half until I could find "the one"! As usual, Whiteflash
was a pleasure to do business with!
Edit...Probably should thank my DH for putting up with me for the last 26 years!
