|
|
|
|
| ||
Diamond Jewelry Forums
 Picture Gallery
 Video Gallery
 Journal
|
|||
|
|  Search
|  Posted Today
|  Most Active
|  Help
|
||
 »
Home
»  » Diamond Prices and Grading »
 » RockyTalky
»  » Dumb questions ahead about Tacori, soldering,diamond color etc
|
|
 |
Dumb questions ahead about Tacori, soldering,diamond color etc |
 |
| P: 10/30/2004 9:29:51 AM | |
PunchNPie75 Ideal Rock Total Posts: 1,227 Last Post: 2/9/2008 Member Since: 8/5/2004 |
Hi all I am thinking of resetting my 1 carat stone into a Tacori Rosebud setting, and then getting the matching band. I want to order both with the diamonds halfway around the band. My questions: 1- My stone is 1.07 RB H SI1. Tacori uses for their side and pave stones G color stones accoring to my research. Is there are visible difference in a 3 stone setting between two small G color stones and a center H color stone? My current stone is ideal cut and faces up white in my current platinum setting 2- This style ring has stones/scalloping on the sides (well maybe that should say the front and back?) of the rings. I don't know much about soldering rings but if you have half band of pave stones on the front/back of the rings, can you solder rings? do they only solder the ring in the back of the shank or all the way around? I hope I am wording what I am trying to say right. Thank you! My favorite color is sparkle!!! |
| Posted: 10/30/2004 9:29:51 AM | |
|
There are 2 replies to this message. There are 2 replies on this page. |
|
| P: 10/30/2004 7:48:10 PM | |
ninasstar Cut Rock Total Posts: 100 Last Post: 3/29/2005 Member Since: 10/2/2004 |
Hi there. I just received my tacori rings....i have the full eternity ring with matching band. My set is not the rosebud, but it's exactly the same, minus the two little diamonds on the side of the center stone. My center stone is a 1.54 I color stone......and it looks absolutely fine next to the little G color diamonds....so your H will be just fine. I wouldn't even worry about that if I were you. As far as soldering the two rings together, I don't know that I would. My rings sit perfectly next to eachother....you may want to try wearing them first and see...you may not end up wanting to solder them together. Good luck.
|
| Posted: 10/30/2004 7:48:10 PM | |
| P: 10/30/2004 10:16:05 PM | |
laney Ideal Rock Total Posts: 750 Last Post: 7/27/2006 Member Since: 12/18/2003 |
Hi I just got my tacori rosebud setting 3 weeks ago. pictures (bad..) are in the "show me the ring". I have a 1.5 round in the center - and my stone is an F - but I think your H will be just fine. Also - I too say, try the rings first just "together". They fit very nicely against one another - and don't seem to spin. i was a bit concerned regarding the diamonds on the sides wearing against one another - which I am sure will happen over time - but they don't seem to rub so much. In addition - if you plan to get them soldered anyway - maybe have them not put diamonds on the inner sides of the two rings. Why pay for that when you won't see it when it's together. I'm sure they can do that - and save you a little $$ Good Luck with the set. I still am in awe...it's so pretty! Laney |
| Posted: 10/30/2004 10:16:05 PM | |
 Previous Page
|
Next Page 
|
Contact Us | Back Home | Privacy Statement | Forum Agreement | Forum Policies | |
| Ideal BB Version: 0.1.5.4.beta1 | Message forum software powered by the Ideal BB |
| |
Pricescope -
Knowledge -
Diamond Prices -
Tools -
Resources -
About
© 2000-2009 Pricescope. Terms of Use Privacy Policy Disclaimer
forum archives
